Aceex NR22-Y
Talk0
1,179pages on
this wiki
this wiki
Your here: Home / Network / Hardware Specific / Aceex / NR22-Y
 |
This article is a stub. Please help InfoDepot Wiki by expanding it, adding pictures, and improving existing text.
|
| Aceex NR22-Y | |
|---|---|
 | |
|
Homepage | |
|
Wikipedia |
? |
|
dd-wrt |
? |
|
OpenWRT |
? |
|
Tomato |
? |
|
TomatoUSB |
Not Supported |
|
Gargoyle |
? |
Contents |
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.
Specs
Edit
This section is in need of cleanup!
Platform
Serial Num. = ? FCC ID = IFA-NRXX CPU Type = Ralink RT3052F MIPS Rev = ? CPU Speed = 380MHz Bus = ? Flash Type = Parallel Flash Chip = ? Flash Size = 4MB Max Firmware Size = ? RAM Size = 32MN RAM Chip = ? nvram Size = ? Switch = Ralink RT3052F (SoC) Port-based vlan = ? 802.1q vlan = ? Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN Wired Standard = IEEE 802.3/3u boot_wait = ? bootloader = ? Flash Card Socket/Type = ? SD/MMC Mod Support = No MiniPCI slots = No PoE = No Power = 5V/2A ? Color of LEDs = ? Size = ? USB = No Serial Port = ? JTAG Port = ? Supported by TJTAG/Version = ? Supported by dd-wrt as of = NR22 v.24SP2 - build 12826 - 20090904 dd-wrt K2.4 Support = ? dd-wrt K2.6 Support = ? Special Features = ?
Radio
Wireless Radio = Ralink RT3052F (SoC) WLAN DSP processor = ? Antenna Connector Type = 2x RP-SMA Wireless Standard = IEEE 802.11b/g/n WiFi Operating Frequency = 2.4GHz 802.11n draft 2.0 = up to 300Mbps 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b = 1, 2, 5.5, 11Mbps Radio cor_rev = ? Radio Capabilities = ?
Links of InterestEdit
This section is in need of cleanup!
FlashingEdit
This section is in need of cleanup!
UpgradingEdit
This section is in need of cleanup!
RevertingEdit
This section is in need of cleanup!
JTAG/Serial InfoEdit
JTAGEdit
JTAG PinoutsEdit
This section is in need of cleanup!
JTAG RecoveryEdit
This section is in need JTAG Recovery Instructions!
SerialEdit
Serial PinoutsEdit
This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories -
Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
Bits per second = 115200
Data Bits = 8
Parity = none
Stop bits = 1
Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you
don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open
Serial RecoveryEdit
This section is in need of Serial Recovery Instructions!
vlan InfoEdit
This section is in need of cleanup!
PicturesEdit
FCC PicturesEdit
NotesEdit
Hardware ModificationEdit
