FANDOM


Your here: Home / Network / Hardware Specific / Airlink 101 / Airlink 101 AR690W


Airlink 101 AR690W
Airlink 101 AR690Wa

Homepage

AR690W

Wikipedia

?

dd-wrt

?

OpenWRT

?

Tomato

?

TomatoUSB

Not Supported

Gargoyle

?

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

SpecsEdit

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = RRK-WRGN20
CPU Type = Ralink RT2880F GY57600D0 0821ST
MIPS Rev = ?
CPU Speed = 266MHz
Bus = ?
Flash Type = Parallel
Flash Chip = ?
Flash Size = 4MB
Max Firmware Size = 3735552 bytes
RAM Size = 32MB
RAM Chip = 0823PPR V54C3256164VDT7
nvram Size = ?
Switch = Realtek RTL8366SR 82416S3 G819B
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100/1000-WAN 4-10/100/1000-LAN
Wired Standard = IEEE 802.3/3u/3ab
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 5V/3A
Color of LEDs = ?
Size = 225 x 120 x 30mm (L x W x H)
USB = No
Serial Port = Yes
JTAG Port = No
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = v.24 sp2 - build 13908 - 20100213
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = ?

Radio

Wireless Radio = Ralink RT2820L
WLAN DSP processor = ?
Antenna Connector Type = 3 external 2dBi undetachable antennas
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz
 802.11n draft 2.0 = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

FlashingEdit

Fixme This section is in need of cleanup!

UpgradingEdit

Fixme This section is in need of cleanup!

RevertingEdit

Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit

JTAGEdit

JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!

SerialEdit

Serial PinoutsEdit
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

USB InfoEdit

Fixme This section is in need of cleanup!

vlan InfoEdit

Fixme This section is in need of cleanup!

PicturesEdit

Airlink 101 AR690Wb

FCC PicturesEdit

Airlink 101 AR690W FCC a Airlink 101 AR690W FCC b Airlink 101 AR690W FCC c

Airlink 101 AR690W FCC d Airlink 101 AR690W FCC e Airlink 101 AR690W FCC f

Airlink 101 AR690W FCC g Airlink 101 AR690W FCC h Airlink 101 AR690W FCC i

Airlink 101 AR690W FCC j Airlink 101 AR690W FCC k Airlink 101 AR690W FCC l

NotesEdit


Hardware ModificationEdit


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.