Allnet ALL0285
Talk0
1,179pages on
this wiki
this wiki
Revision as of 13:09, June 20, 2011 by WifiShadow (Talk | contribs)
Your here: Home / Network / Hardware Specific / Allnet / ALL0285
 |
This article is a stub. Please help InfoDepot Wiki by expanding it, adding pictures, and improving existing text.
|
| Allnet ALL0285 | |
|---|---|
 | |
|
Homepage |
? |
|
Wikipedia |
? |
|
dd-wrt | |
|
OpenWRT |
? |
|
Tomato |
? |
|
TomatoUSB |
Not Supported |
|
Gargoyle |
? |
Contents |
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.
Specs
Edit
This section is in need of cleanup!
Platform
Serial Num. = ? FCC ID = ? CPU Type = Atheros AR2312A MIPS Rev = ? CPU Speed = 180MHz Bus = ? Flash Type = ? Flash Chip = ? Flash Size = 4MB Max Firmware Size = 3801088 bytes RAM Size = 16MB RAM Chip = ? nvram Size = ? Switch = ? nvram Size = ? Port-based vlan = ? 802.1q vlan = ? Ethernet Port Count = 1-LAN Wired Standard = IEEE 802.3?/3af boot_wait = ? bootloader = ? Flash Card Socket/Type = ? SD/MMC Mod Support = ? MiniPCI slots = ? PoE = Yes Power = 5V/1.2A Color of LEDs = ? Size = ? USB = ? Serial Port = Yes JTAG Port = Yes Supported by TJTAG/Version = ? Supported by dd-wrt as of = WIP dd-wrt K2.4 Support = ? dd-wrt K2.6 Support = ? Special Features = same hardware as DWL-2100
Radio (ath0)
Wireless Radio = Atheros WLAN DSP processor = ? Antenna Connector Type = ? Wireless Standard = IEEE 802.11b/g WiFi Operating Frequency = ? 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b = 1, 2, 5.5, 11Mbps Radio cor_rev = ? Radio Capabilities = ?
Links of InterestEdit
FlashingEdit
UpgradingEdit
RevertingEdit
JTAG/Serial InfoEdit
JTAGEdit
JTAG PinoutsEdit
This section is in need of cleanup!
JTAG RecoveryEdit
This section is in need JTAG Recovery Instructions!
SerialEdit
Serial PinoutsEdit
This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories -
Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
Bits per second = 115200
Data Bits = 8
Parity = none
Stop bits = 1
Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you
don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open
Serial RecoveryEdit
This section is in need of Serial Recovery Instructions!
vlan InfoEdit
This section is in need of cleanup!
PicturesEdit
This section is in need of cleanup!
FCC PicturesEdit
This section is in need of cleanup!
NotesEdit
Hardware ModificationEdit
