InfoDepot Wiki

Asus RT-G32 B1

1,124pages on
this wiki
Add New Page
Talk0 Share

Your here: Home / Network / Hardware Specific / Asus / RT-G32 B1

Asus RT-G32 B1
Asus RT-G32a



Asus Routers








Not Supported



NOTE: This divice is not supported by dd-wrt.


Fixme This section is in need of cleanup!


Serial Num. = ?
CPU Type = Ralink RT3050
MIPS Rev = ?
CPU Speed = 320MHz
Bus = 16Bit
Flash Type = Serial
Flash Chip = ?
Flash Size = 4MB
Max Firmware Size = 3801088 bytes
RAM Size = 16MB
RAM Chip = ?
nvram Size = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100M-WAN 4-10/100M-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/1A
Color of LEDs = ?
Size = 167 x 110 x 33 ( not including the size of Antenna) mm
USB = No
Serial Port = Yes
JTAG Port = No
Supported by TJTAG 3.02 = ?
Supported by dd-wrt as of = ?
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = ?


Wireless Radio = Ralink
WLAN DSP processor = ?
Antenna Connector Type = ?
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz - 2.5GHz
 802.11n Draft = up to 150Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Channels = 11 CH (US, Canada), 13 CH (EU), 14 CH (Japan)
Transmitted Power = 11b: 18 dBm, 11g: 15 dBm
Receiver Sensitivity =	IEE802.11b: -88 dBm(Typical)
                        IEE802.11g: -74 dBm(Typical)
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest


Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!

JTAG/Serial Info




Serial Pinouts
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
 Bits per second = 57600
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 57600
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 57600
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

vlan Info

Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!

FCC Pictures

Asus RT-G32 FCCa Asus RT-G32 FCCb Asus RT-G32 FCCc
Asus RT-G32 FCCd Asus RT-G32 FCCe Asus RT-G32 FCCf
Asus RT-G32 FCCg Asus RT-G32 FCCh Asus RT-G32 FCCi
Asus RT-G32 FCCj


Hardware Modification

Ad blocker interference detected!

Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.