FANDOM


Your here: Home / Network / Hardware Specific / Asus / RT-N10+


Asus RT-N10+
Asus RT-N10+a

Homepage

http://www.asus.com

Wikipedia

Asus Routers

dd-wrt

WIP

OpenWRT

?

Tomato

?

TomatoUSB

Not Supported

Gargoyle

?

NOTE: This divice is WIP

Specs

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = ?
CPU Type = Ralink RT3050F
MIPS Rev = ?
CPU Speed = ?
Bus = ?
Flash Type = Parallel
Flash Chip = SPANSION S29GL032N
Flash Size = 4MB
Max Firmware Size = 3801088 bytes
RAM Size = 128MB
RAM Chip = AOTOM A128168L-6TE
nvram Size = ?
Switch = Ralink RT3050F (SoC)
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100M-WAN 4-10/100M-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/0.5A
Color of LEDs = ?
Size = ?
USB = No
Serial Port = Yes
JTAG Port = Yes
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = Support started 15459
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = Japan Market only?

Radio

Wireless Radio = Ralink RT3050F (SoC)
WLAN DSP processor = ?
Antenna Connector Type = 1 x 3dbi external fixed antenna
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4~2.4835GHz
802.11n Draft 2.0 = up to 150Mbps
802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest

Flashing

Fixme This section is in need of cleanup!

Files Asus-RT-N10PLUS

Upgrading

Fixme This section is in need of cleanup!

Reverting

Fixme This section is in need of cleanup!

JTAG/Serial Info

JTAG

JTAG Pinouts
Fixme This section is in need of cleanup!
JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts

Four Pins J2 is for the serial port communication.

PIN 1 = VCC (3.3 V)
PIN 2 = GND
PIN 3 = TX
PIN 4 = RX

Also set Baud rate to 57600 instead of recommended 115200 for the communication to work

Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

vlan Info

Fixme This section is in need of cleanup!

Pictures

Asus RT-N10+b

FCC Pictures

Fixme This section is in need of cleanup!

Notes

Hardware Modification

Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.