Fandom

InfoDepot Wiki

Asus WL-300g

1,124pages on
this wiki
Add New Page
Talk0 Share

Your here: Home / Network / Hardware Specific / Asus / WL-300g


Asus WL-300g
Asus WL-300ga

Homepage

WL-300G

Wikipedia

?

dd-wrt

?

OpenWRT

?

Tomato

?

TomatoUSB

Not Supported

Gargoyle

?

WARNING: It is recommended to use ASUS Firmware restoration tool for ASUS routers initial flash
(use *.TRX file)

NOTE: Requires VINT, Do not flash anything else.
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = MSQWL300G
CPU Type = Broadcom BCM4710
MIPS Rev = ?
CPU Speed = 125MHz
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = 4MB
Max Firmware Size = 3801088 bytes
RAM Size = 16MB
RAM Chip = ?
nvram Size = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = CFE
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = Yes
PoE = No
Power = 5
Color of LEDs = ?
Size = ?
USB = No
Serial Port = ?
JTAG Port = Yes
Supported by TJTAG 3.02 = ?
Supported by dd-wrt as of = v24
dd-wrt K2.4 Support = Yes
dd-wrt K2.6 Support = No
Special Features = initial flash via Asus tool, VINTage firmware needed.

Radio (wl0)

Wireless Radio = Broadcom
WLAN DSP processor = ?
Antenna Connector Type = Internal
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = ?
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities =?

Links of Interest

Fixme This section is in need of cleanup!

Flashing

Fixme This section is in need of cleanup!

Upgrading

If dd-wrt is already on the router follow these instructions. If stock firmware is on the router follow the flashing instructions.

  1. Check for recommended builds here first.
  2. Set your computer to a static IP of 192.168.1.7. (or to whatever subnet the router is on) Disable all firewalls and security. Disable wireless on your computer and only have the router connected to the flashing computer by the ethernet cable between the two.
  3. Hard reset or 30/30/30 (If the router supports it, if not, reset to defults in the GUI) prior to flashing. Wait. Check for password page on re-login and change password.
  4. Flash firmware. You can use the webgui except if you have a belkin router. (For belkin use tftp.exe to flash)
  5. Wait...at least three minutes. Lights should return to normal. See important2, below. Failing to wait is how most people brick their routers.
  6. Do a power cycle of the router. (Unplug the cord, count to 30 and plug it back in.)
  7. Wait for the lights to return to normal usually about 2 minutes.
  8. Hard reset or 30/30/30 again (If the router supports it, if not, reset to defults in the GUI). Wait. Check for the password page and re-login to change the password. Then you can reconfigure your settings manually.
  9. Once configured set your computer back to autoIP and autoDNS.

Important1: This Hard reset or 30/30/30 works fine for Asus router, but you do have to power cycle after the reset.

Important2: After you flash the firmware, and before you do the hard reset, the router will be building some nvram settings. YOU MUST WAIT FOR THIS TO FINISH PRIOR TO DOING ANYTHING WITH THE ROUTER INCLUDING A HARD RESET. Usually, you can tell when this process is completed by the WAN light coming on, but it does take several minutes. Go have a beer. There are starting to be more and more people who BRICK their routers by not waiting until the nvram is rebuilt, PRIOR to doing a hard reset. YOU NEED TO WAIT!

Reverting

Fixme This section is in need of cleanup!

JTAG/Serial Info

JTAG

JTAG Pinouts
Fixme This section is in need of cleanup!
JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

vlan Info

Fixme This section is in need of cleanup!

Pictures

Asus WL-300gb Asus WL-300gc Asus WL-300gd

Asus WL-300ge

FCC Pictures

Asus WL-300g FCCa Asus WL-300g FCCb Asus WL-300g FCCc

Asus WL-300g FCCd Asus WL-300g FCCe Asus WL-300g FCCf

Asus WL-300g FCCg Asus WL-300g FCCh Asus WL-300g FCCi

Asus WL-300g FCCj

Notes


Hardware Modification


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.