FANDOM


Your here: Home / Network / Hardware Specific / Belkin / F5D7130


Belkin F5D7130
Belkin F5D7130a

Homepage

Belkin F5D7130

Wikipedia

?

dd-wrt

Supported Devices Belkin

OpenWRT

Not for 2MB Devices

Tomato

Not for 2MB Devices

TomatoUSB

Not for 2MB Devices

NOTE: Requires Micro, Do not flash anything else.
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

SpecsEdit

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = K7SF5D7130
CPU Type = Broadcom BCM4710
MIPS Rev = ?
CPU Speed = 125MHz
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = 2MB
Max Firmware Size = 1769472 bytes
RAM Size = ?MB
RAM Chip = ?
nvram Size = 32kb
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = CFE
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = 1
PoE = ?
Power = ?
Color of LEDs = ?
Size = ?
USB = No
Serial Port = ?
JTAG Port = ?
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = ?
dd-wrt K2.4 Support = Yes
dd-wrt K2.6 Support = No
Special Features = Requires micro

Radio (wl0)

Wireless Radio = Broadcom
WLAN DSP processor = ?
Antenna Connector Type = Dual dipole fixed antenna
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = 2400-2483.5GHz
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

Fixme This section is in need of cleanup!

FlashingEdit

Fixme This section is in need of cleanup!

UpgradingEdit

Fixme This section is in need of cleanup!

RevertingEdit

Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit

JTAGEdit

JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!

SerialEdit

Serial PinoutsEdit
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

vlan InfoEdit

Fixme This section is in need of cleanup!

PicturesEdit

Belkin F5D7130b Belkin F5D7130c Belkin F5D7130d

Belkin F5D7130e Belkin F5D7130f Belkin F5D7130g

FCC PicturesEdit

Belkin F5D7130 FCC a Belkin F5D7130 FCC b Belkin F5D7130 FCC c

Belkin F5D7130 FCC d Belkin F5D7130 FCC e Belkin F5D7130 FCC f

Belkin F5D7130 FCC g Belkin F5D7130 FCC h Belkin F5D7130 FCC i

Belkin F5D7130 FCC j Belkin F5D7130 FCC k

NotesEdit

Hardware ModificationEdit

Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.