FANDOM


Your here: Home / Network / Hardware Specific / Belkin / F7D8301 v1
(Play N600 HD Wireless Dual-Band N+ Router)


Belkin F7D8301 v1
Belkin F7D8302 v1 a
Play N600 HD Wireless Dual-band N Router

Homepage

F7D8301

Wikipedia

?

dd-wrt

?

OpenWRT

?

Tomato

?

TomatoUSB

Not Supported

Gargoyle

?

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

SpecsEdit

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = K7SF7D4301V1 ?
CPU Type = ?
MIPS Rev = ?
CPU Speed = ?
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = ?
Max Firmware Size = ?
RAM Size = ?
RAM Chip = ?
nvram Size = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = ?
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = ?
PoE = ?
Power = ?
Color of LEDs = ?
Size = ?
USB = ?
Serial Port = ?
JTAG Port = ?
Supported by TJTAG/Version = ?
Special Features = ?

Radio

Wireless Radio = ?
WLAN DSP processor = ?
Antenna Connector Type = ?
Wireless Standard = ??? IEEE 802.11a/b/g/n
WiFi Operating Frequency = ?
 ??? 802.11n = up to 300Mbps
 ??? 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 ??? 802.11b = 1, 2, 5.5, 11Mbps
 ??? 802.11a = 6, 9, 12, 18, 24, 36, 48, 54Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

FlashingEdit

Fixme This section is in need of cleanup!

UpgradingEdit

Fixme This section is in need of cleanup!

RevertingEdit

Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit

JTAGEdit

JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!

SerialEdit

Serial PinoutsEdit
J3 |> [+ TX RX -]

or

1. 3.3
2. TX
3. RX
4. GND
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Mincom setup in LinuxEdit
After installing minicom, run it with -s flag for setup (sudo minicom -s)
  Under "Serial Port Setup":
  Use 'A' to set the serial device (ie. /dev/ttyUSB0)
  Use 'E' to set the Bps/Par/Bits
    Speed (baud) = 115200
    Data bits = 8
    Stop bits = 1
    Parity = None
    Flow control = None
 Save as dfl
Serial RecoveryEdit
1. Clear the nvram
2. Type ifconfig and you should get '=0', then it succeeded.
3. Note the ip address listed and netmask address. 
4. After you have used the ifconfig command wait a minute or two. 
5. In your web browser got to the IP address noted in step 4.
6. Upload DD-WRT mini image or original firmware.

Example:
CFE> nvram erase
CFE> ifconfig
=0
CFE>

TFTP Recovery

Coming Soon

USB InfoEdit

Fixme This section is in need of cleanup!

vlan InfoEdit

Fixme This section is in need of cleanup!

PicturesEdit

Fixme This section is in need of cleanup!

FCC PicturesEdit

Fixme This section is in need of cleanup!

NotesEdit


F7D8301 v1 Chips

Broadcom Dual band (2.4 GHz/5GHz) Wireless Radio:  BCM4718A1KFBG

Broadcom Smart Gigabit Switch: BCM53115SKFBG

EtronTech DDR2 32MX16BIT SDRAM: EM68B16CWPA-25h

cFeon NVRAM: EN29lV640B-90TIP

Sticker over cFeon NVRAM: WG8117F22 2-LF-AK


Hardware ModificationEdit


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.