Fandom

InfoDepot Wiki

Belkin F9K1103 v1

1,124pages on
this wiki
Add New Page
Talk0 Share

Your here: Home / Network / Hardware Specific / Belkin / F9K1103 v1

Belkin F9K1103 v1
Belkin F9K1103 v1a
N750 DB Wireless Dual-Band N+ Router

Homepage

Belkin F9K1103 v1

Wikipedia

Belkin

WikiDevi

Belkin F9K1103

dd-wrt

Not Supported

OpenWRT

Not Supported

Tomato

Not Supported

TomatoUSB

Not Supported

Gargoyle

Not Supported


NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs

Fixme This section is in need of cleanup!

Platform

Serial Num. = 12113
FCC ID = K7SF9K1103V1
Industry Canada ID = 3623A-F9K1103V1
CPU Type = RaLink RT3883F P4G5150G0 1117AT (SoC)
MIPS Rev = ?
CPU Speed = 500MHz
Bus = ?
Flash Type = SPI Flash
Flash Chip = MXIC MX, 25L6406E, M2I-12G, 3F967500, L111983
Flash Size = 8MB
Max Firmware Size = ?
RAM Size = 64MB
RAM Chip = EtronTech EM68B16CWPA-25H, P058160BFS47511ZQ
nvram Size = ?
Switch = Realtek RTL8367R B5C26P4 GB20B
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100/1000-WAN 4-10/100/1000-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = Uboot
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/2A
Color of LEDs = 1 x network status LED, 1 x WPS LED
Size = ?
USB = 2x USB2.0
Serial Port = Yes
JTAG Port = No
Supported by TJTAG/Version = No JTAG port
Special Features = ?

Radio

Wireless Radio = RaLink RT3883F P4G5150G0 1117AT (SoC)
WLAN DSP processor = ?
Antenna Connector Type = 2x2, Internal
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4Ghz
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Radio

Wireless Radio = RaLink RT3092L PBG173010 1120ST
WLAN DSP processor = ?
Antenna Connector Type = 3x3, Internal
Wireless Standard = IEEE 802.11a/n
WiFi Operating Frequency = 5Ghz
 802.11n = up to 450Mbps
 802.11a = 6, 9, 12, 18, 24, 36, 48, 54Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest

Flashing

Fixme This section is in need of cleanup!

Upgrading

Fixme This section is in need of cleanup!

Reverting

Fixme This section is in need of cleanup!

JTAG/Serial Info

JTAG

No JTAG port

Serial

Serial Pinouts
 Front
 VCC  1 o
  RX  2 o
  TX  3 o
 GND  4 o
 Rear 
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

USB Info

Fixme This section is in need of cleanup!

vlan Info

Fixme This section is in need of cleanup!

Pictures

Belkin F9K1103 v1b Belkin F9K1103 v1c Belkin F9K1103 v1d

FCC Pictures

Belkin F9K1103 v1 FCCa Belkin F9K1103 v1 FCCb Belkin F9K1103 v1 FCCc

Belkin F9K1103 v1 FCCd Belkin F9K1103 v1 FCCe Belkin F9K1103 v1 FCCf

Belkin F9K1103 v1 FCCg Belkin F9K1103 v1 FCCh Belkin F9K1103 v1 FCCi

Belkin F9K1103 v1 FCCj Belkin F9K1103 v1 FCCk Belkin F9K1103 v1 FCCl

Belkin F9K1103 v1 FCCm Belkin F9K1103 v1 FCCn Belkin F9K1103 v1 FCCo

Belkin F9K1103 v1 FCCp Belkin F9K1103 v1 FCCq

Notes

Hardware Modification


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.