Fandom

InfoDepot Wiki

Compex NP28G

1,124pages on
this wiki
Add New Page
Talk0 Share

Your here: Home / Network / Hardware Specific / Compex / NP28G


Compex NP28G
Compex NP28Ga

Homepage

http://www.compex.com.sg
http://www.cpx.cz

Wikipedia

?

dd-wrt

Supported

OpenWRT

Supported

Tomato

Not Supported

TomatoUSB

Not Supported

NOTE: Activation Required.
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

SpecsEdit

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = ?
CPU Type = Infineon ADM5120
MIPS Rev = ?
CPU Speed = 175MHz
Bus = ?
Flash Type = Parallel
Flash Chip = MX29LV320CBTC-70G
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 32MB
RAM Chip = IC42S32400-7T
nvram Size = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN 3-10/100-LAN
Wired Standard = IEEE 802.3/3u/3af
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = none
SD/MMC Mod Support = No
MiniPCI slots = Yes (1)
PoE = Yes
Power = 5V ?A
Color of LEDs = green/blue
Size = 174 x 40 x 104mm
USB = VIA Vectro VT6212 - 4-port USB 2.0 Host Controller
Serial Port = 1
JTAG Port = Yes
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = NP28G v.24SP2 build 11267
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = needs DD-WRT activation

Radio

Wireless Radio = Compex WLM54G (Atheros)
WLAN DSP processor = ?
Antenna Connector Type = (Internal)U.FL (External)Fixed?
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = 2.4Ghz
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54, 108Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

FlashingEdit

Fixme This section is in need of cleanup!

UpgradingEdit

Fixme This section is in need of cleanup!

RevertingEdit

Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit

JTAGEdit

JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!

SerialEdit

Serial PinoutsEdit
 gnd  o o
      o o
      o o rx
      o o tx
      o o
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

USB InfoEdit

Fixme This section is in need of cleanup!

vlan InfoEdit

Fixme This section is in need of cleanup!

PicturesEdit

Compex NP28Gb

FCC PicturesEdit

Fixme This section is in need of cleanup!

NotesEdit


Hardware ModificationEdit


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.