Wikia

InfoDepot Wiki

Conceptronic C54APT

Talk0
1,178pages on
this wiki

Your here: Home / Network / Hardware Specific / Conceptronic / C54APT


Conceptronic C54APT
Conceptronic C54APTa

Homepage

?

Wikipedia

?

dd-wrt

?

OpenWRT

?

Tomato

?

TomatoUSB

Not Supported

Gargoyle

?

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

SpecsEdit

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = ?
CPU Type = Atheros AR2312A
MIPS Rev = ?
CPU Speed = 180MHz
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 16MB
RAM Chip = ?
nvram Size = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = ?
PoE = ?
Power = 5V/1.2A
Color of LEDs = ?
Size = ?
USB = ?
Serial Port = Yes
JTAG Port = Yes
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = WIP
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = same hardware as D-Link DWL-2100AP

Radio (ath0)

Wireless Radio = Atheros AR2112A
WLAN DSP processor = ?
Antenna Connector Type = ?
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = ?
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

Fixme This section is in need of cleanup!

FlashingEdit

Fixme This section is in need of cleanup!

UpgradingEdit

Fixme This section is in need of cleanup!

RevertingEdit

Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit

JTAGEdit

JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!

SerialEdit

Serial PinoutsEdit
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

USB InfoEdit

Fixme This section is in need of cleanup!

vlan InfoEdit

Fixme This section is in need of cleanup!

PicturesEdit

Fixme This section is in need of cleanup!

FCC PicturesEdit

Fixme This section is in need of cleanup!

NotesEdit


Hardware ModificationEdit


Advertisement | Your ad here

Around Wikia's network

Random Wiki