D-Link DAP-1350
Talk0
1,179pages on
this wiki
this wiki
Your here: Home / Network / Hardware Specific / D-Link / DAP-1350
 |
This article is a stub. Please help InfoDepot Wiki by expanding it, adding pictures, and improving existing text.
|
| D-Link DAP-1350 | |
|---|---|
 | |
|
Homepage | |
|
Wikipedia |
? |
|
dd-wrt |
not supported |
|
OpenWRT |
supported in Atttude Adjustment/trunk |
|
Tomato |
not supported |
|
TomatoUSB |
not supported |
|
Gargoyle |
Not Supported |
Contents |
NOTE: During configuration or flashing of a device, the only thing that should be hooked to the device is the computer and power.
Specs
Edit
This section is in need of cleanup!
Platform
Serial Num. = ? FCC ID = ? CPU Type = Ralink RT3052F SoC with MIPS32 24KEc core MIPS Rev = ? CPU Speed = 320/384MHz Bus = ? Flash Type = ? Flash Chip = ? Flash Size = 8MB Max Firmware Size = ? RAM Size = 32M RAM Chip = ? nvram Size = ? Switch = Ralink SoC internal Port-based vlan = ? 802.1q vlan = ? Ethernet Port Count = 1-10/100-LAN/WAN Wired Standard = IEEE 802.3? boot_wait = ? bootloader = U-Boot Flash Card Socket/Type = ? SD/MMC Mod Support = ? MiniPCI slots = ? PoE = ? Power = ? Color of LEDs = Blue/Red Size = ? USB = 1 USB Serial Port = Yes JTAG Port = ? Supported by TJTAG/Version = ? Special Features = ?
Radio
Wireless Radio = Ralink SoC (MAC RT2860, RF RT3022?) WLAN DSP processor = Ralink SoC (MAC RT2860, RF RT3022?) Antenna Connector Type = Internal Wireless Standard = 802.11b/g/n WiFi Operating Frequency = 2.4GHz 802.11n = up to 300Mbps 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b = 1, 2, 5.5, 11Mbps Radio cor_rev = ? Radio Capabilities = ?
Links of InterestEdit
FlashingEdit
This section is in need of cleanup!
UpgradingEdit
This section is in need of cleanup!
RevertingEdit
This section is in need of cleanup!
JTAG/Serial InfoEdit
JTAGEdit
JTAG PinoutsEdit
This section is in need of cleanup!
JTAG RecoveryEdit
This section is in need JTAG Recovery Instructions!
SerialEdit
Serial PinoutsEdit
This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories -
Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
Bits per second = 115200
Data Bits = 8
Parity = none
Stop bits = 1
Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you
don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open
Serial RecoveryEdit
This section is in need of Serial Recovery Instructions!
USB InfoEdit
This section is in need of cleanup!
vlan InfoEdit
This section is in need of cleanup!
PicturesEdit
FCC PicturesEdit
This section is in need of cleanup!
