Your here: Home / Network / Hardware Specific / Belkin / F7D3301 v1
 |
This article is a stub. Please help InfoDepot Wiki by expanding it, adding pictures, and improving existing text.
|
|
File:Belkin_F7D3301_v1.0a.jpg Share Max Wireless Router |
WARNING: Always use TFTP to flash Belkin routers if at all possible! Upgrading dd-wrt from the web interface can lead to a bricked (nonfunctional) unit!
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.
Specs[]
This section is in need of cleanup!
Platform
Serial Num. = ? FCC ID = K7SF7D3301V1 CPU Type = Broadcom BCM4718A1KFBG (BCM4718) MIPS Rev = ? CPU Speed = 480MHz Bus = ? Flash Type = Parallel Flash Chip = CFEON (EON) EN29LV640B Flash Size = 8MB Max Firmware Size = 7995392 bytes RAM Size = 64MB RAM Chip = EtronTech EM68B16CWPA-25H N208160AFL03811ZQ (32M x 16 bit DDRII Synchronous DRAM (SDRAM)) Etron Technology, Inc. nvram Size = ? Switch = Broadcom BCM53115SKFBG (BCM53115) Port-based vlan = ? 802.1q vlan = ? Ethernet Port Count = 1-10/100/1000-WAN 4-10/100/1000 Wired Standard = IEEE 802.3? boot_wait = ? bootloader = CFE Flash Card Socket/Type = No SD/MMC Mod Support = No MiniPCI slots = No PoE = No Power = 12v 1.5A Color of LEDs = ? Size = ? USB = 2x USB 2.0 Serial Port = Yes JTAG Port = Yes Supported by TJTAG 3.02 = ? Supported by dd-wrt as of = v24 k2.6 15156 dd-wrt K2.4 Support = No dd-wrt K2.6 Support = Yes Special Features = WIP, gigaswitch
Radio (wl0)
Wireless Radio = Broadcom BCM4718A1KFBG (BCM4718 SoC) WLAN DSP processor = ? Antenna Connector Type = Internal Wireless Standard = IEEE 802.11b/g/n WiFi Operating Frequency = 2.4GHz 802.11n Draft = up to 300Mbps 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b = 1, 2, 5.5, 11Mbps Radio cor_rev = ? Radio Capabilities = ?
Links of Interest[]
Flashing[]
This section is in need of cleanup!
Upgrading[]
This section is in need of cleanup!
Reverting[]
This section is in need of cleanup!
JTAG/Serial Info[]
JTAG[]
JTAG Pinouts[]
This section is in need of cleanup!
JTAG Recovery[]
This section is in need JTAG Recovery Instructions!
Serial[]
J1 header available. 1-TX 2-RX 3-GND
Serial Pinouts[]
This section is in need of cleanup!
Hyper terminal Setup in Windows XP[]
In Windows XP, Click Start Button - All Programs - Accessories -
Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
Bits per second = 115200
Data Bits = 8
Parity = none
Stop bits = 1
Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you
don't have to enter the settings again.
Putty Setup in Windows XP[]
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open
Serial Recovery[]
This section is in need of Serial Recovery Instructions!
USB Info[]
The USB port is where you can connect an external USB hard drive or flash drive. Which can do a multitude of things. You can use in as a NAS, storage for a FTP server, use Optware to run external programs like torrent software, samba for sharing files to your network, share a USB printer with your network... The list of possibilities is long, it just takes a little research.
ProFTPd is included in most the newer builds of dd-wrt. Check the features chart to be sure.
A ftp server, file sharing, and a media sever is included in TomatoUSB if your device is compatable.
vlan Info[]
This section is in need of cleanup!
Pictures[]
FCC Pictures[]
Notes[]
Hardware Modification[]