InfoDepot Wiki

READ MORE

InfoDepot Wiki
Register
Advertisement

Your here: Home / Network / Hardware Specific / Cisco-Linksys / E1000 v2.0


File:Linksys_E1000a.jpg
Wireless-N Router

NOTE: Requires K2.6, Do not flash anything else.
NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power.

Specs[]

Fixme This section is in need of cleanup!

Platform

Serial Num. = CVN1
FCC ID = Q87-E1000V2
CPU Type = Broadcom BCM5357B0KFBG (BCM5357B)
MIPS Rev = ?
CPU Speed = 300MHz
Bus = ?
Flash Type = Serial
Flash Chip = MX 25L3205D
Flash Size = 4MB
Max Firmware Size = 3801088 bytes
RAM Size = 32MB
RAM Chip = Hynix H5DU2562GTR
nvram Size = 32kb
Switch = Broadcom BCM5357B0KFBG (BCM5357B)
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = CFE
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/0.5A
Color of LEDs = ?
Size = 7.95" x 1.34" x 6.3" (202 x 34 x 160 mm)
USB = No
Serial Port = Yes
JTAG Port = Yes
Supported by TJTAG 3.02 = ?
Supported by dd-wrt as of = 16758
dd-wrt K2.4 Support = No
dd-wrt K2.6 Support = Yes
Special Features = ?

Radio (wl0)

Wireless Radio = Broadcom BCM5357B0KFBG (BCM5357B)
WLAN DSP processor = Broadcom BCM5357B0KFBG (BCM5357B)
Antenna Connector Type = Internal
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz
 802.11n Draft = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest[]

Flashing[]

Fixme This section is in need of cleanup!

Upgrading[]

Fixme This section is in need of cleanup!

Reverting[]

Fixme This section is in need of cleanup!

JTAG/Serial Info[]

JTAG[]

JTAG Pinouts[]
Fixme This section is in need of cleanup!
JTAG Recovery[]
Fixme This section is in need JTAG Recovery Instructions!

Serial[]

Serial Pinouts[]
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP[]
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP[]
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery[]
Fixme This section is in need of Serial Recovery Instructions!

Pictures[]

Pic's from barryware.

Linksys E1000 v2 Linksys E1000 v2 Linksys E1000 v2

Linksys E1000 v2 Linksys E1000 v2 Linksys E1000 v2

FCC Pictures[]

Linksys E1000 v2 Linksys E1000 v2 Linksys E1000 v2

Linksys E1000 v2

With Switch Sample[]

Linksys E1000 v2 Linksys E1000 v2 Linksys E1000 v2

Linksys E1000 v2 Linksys E1000 v2 Linksys E1000 v2

Linksys E1000 v2 Linksys E1000 v2

Without Switch Sample[]

Linksys E1000 v2 Linksys E1000 v2 Linksys E1000 v2

Linksys E1000 v2 Linksys E1000 v2 Linksys E1000 v2

Notes[]


Hardware Modification[]


Advertisement