Your here: Home / Network / Hardware Specific / Gateway / 7001
 |
This article is a stub. Please help InfoDepot Wiki by expanding it, adding pictures, and improving existing text.
|
| File:Gateway_7001a.jpg |
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.
Specs[]
This section is in need of cleanup!
Platform
Serial Num. = ? FCC ID = ? CPU Type = Xscale IXP420 MIPS Rev = ? CPU Speed = 266MHz Bus = ? Flash Type = ? Flash Chip = ? Flash Size = 8MB Max Firmware Size = ? RAM Size = 32MB RAM Chip = ? nvram Size = ? Switch = ? Port-based vlan = ? 802.1q vlan = ? Ethernet Port Count = 1-LAN Wired Standard = IEEE 802.3? boot_wait = ? bootloader = Redboot version 1.92 - built 17:26:35, Dec 4 2003 Flash Card Socket/Type = No SD/MMC Mod Support = No MiniPCI slots = 2 PoE = ? Power = ? Color of LEDs = ? Size = ? USB = No Serial Port = Yes JTAG Port = Yes Supported by TJTAG/Version = ? Supported by dd-wrt as of = v24 RC5 - kernel support dd-wrt K2.4 Support = a/g or g version dd-wrt K2.6 Support = No Special Features = ?
Radio (ath0)
Wireless Radio = atheros WLAN DSP processor = ? Antenna Connector Type = ? Wireless Standard = IEEE 802.11b/g/h WiFi Operating Frequency = 2.4GHz 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b = 1, 2, 5.5, 11Mbps Radio cor_rev = ? Radio Capabilities = ?
Radio (ath1)
Wireless Radio = atheros WLAN DSP processor = ? Antenna Connector Type = ? Wireless Standard = IEEE 802.11a/h WiFi Operating Frequency = 5GHz 802.11a = 6, 9, 12, 18, 24, 36, 48, 54Mbps Radio cor_rev = ? Radio Capabilities = ?
Links of Interest[]
This section is in need of cleanup!
Flashing[]
This section is in need of cleanup!
Upgrading[]
This section is in need of cleanup!
Reverting[]
This section is in need of cleanup!
JTAG/Serial Info[]
JTAG[]
JTAG Pinouts[]
This section is in need of cleanup!
JTAG Recovery[]
This section is in need JTAG Recovery Instructions!
Serial[]
Serial Pinouts[]
There is an 4 pin header near center of the board The pinout is:
- Rx
- (no pin)
- VCC
- GND
- Tx
Baud: 115200 , 8 bits of data, no parity (8N1)
Hyper terminal Setup in Windows XP[]
In Windows XP, Click Start Button - All Programs - Accessories -
Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
Bits per second = 115200
Data Bits = 8
Parity = none
Stop bits = 1
Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you
don't have to enter the settings again.
Putty Setup in Windows XP[]
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open
Serial Recovery[]
This section is in need of Serial Recovery Instructions!
USB Info[]
This section is in need of cleanup!
vlan Info[]
This section is in need of cleanup!
Pictures[]
FCC Pictures[]
This section is in need of cleanup!
Notes[]
Hardware Modification[]