FANDOM


Your here: Home / Network / Hardware Specific / Cisco-Linksys / E1200 v1.0


Linksys E1200 v1.0
Linksys E1200 a
Wireless-N Router

Homepage

E1200

Wikipedia

Linksys Routers

WikiDevi

Linksys E1200 v1

dd-wrt

Linksys E1200 v1

OpenWRT

Status Unknown

Tomato

Status Unknown

TomatoUSB

Status Unknown

Gargoyle

Status Unknown

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

SpecsEdit

Fixme This section is in need of cleanup!

Platform

Serial Num. = 1081
FCC ID = Q87-E1200
Industry Canada ID = 3839A-E1200
CPU Type = Broadcom BCM5357B0
MIPS Rev = ?
CPU Speed = 300MHz
Bus = ?
Flash Type = ?
Flash Chip = Macronix MX25L3206E
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 32MB
RAM Chip = Winbond W9425G6JH-5
nvram Size = ?
Switch = Broadcom BCM5357B0 (SoC)
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = ?
PoE = No
Power = 12VDC/0.5A
Color of LEDs = ?
Size = 7.43" x 1.23" x 5.97"
USB = Possible Mod to add
Serial Port = YES
JTAG Port = ?
Supported by TJTAG/Version = ?
Special Features = ?

Radio

Wireless Radio = Broadcom BCM5357B0 (SoC)
WLAN DSP processor = ?
Antenna Connector Type = 2x2, Internal
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4 GHz
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

FlashingEdit

Fixme This section is in need of cleanup!

UpgradingEdit

Fixme This section is in need of cleanup!

RevertingEdit

Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit

JTAGEdit

JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!

SerialEdit

Serial PinoutsEdit
1 = vcc (3.3v)
2 = tx
3 = rx
4 = n/c
5 = ground
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

vlan InfoEdit

Fixme This section is in need of cleanup!

PicturesEdit

Linksys E1200 b Linksys E1200 c Linksys E1200 d

Linksys E1200 e Linksys E1200 f

FCC PicturesEdit

Fixme This section is in need of cleanup!

NotesEdit


Hardware ModificationEdit