FANDOM


Your here: Home / Network / Hardware Specific / Cisco-Linksys / E1550 v1.0


Linksys E1550 v1.0
File
Wireless-N Router with SpeedBoost

Homepage

E1550

Wikipedia

Linksys Routers

WikiDevi

Linksys E1550

dd-wrt

Status Unknown

OpenWRT

Status Unknown

Tomato

Status Unknown

TomatoUSB

Status Unknown

Gargoyle

Status Unknown

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = Q87-E1550
CPU Type = ?
MIPS Rev = ?
CPU Speed = ?
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = ?
Max Firmware Size = ?
RAM Size = ?
RAM Chip = ?
nvram Size = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = ?
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = ?
PoE = ?
Power = ?
Color of LEDs = ?
Size = ?
USB = ?
Serial Port = ?
JTAG Port = ?
Supported by TJTAG/Version = ?
Special Features = ?

Radio

Wireless Radio = ?
WLAN DSP processor = ?
Antenna Connector Type = ?
Wireless Standard = ??? IEEE 802.11a/b/g/n
WiFi Operating Frequency = ?
 ??? 802.11n = up to 300Mbps
 ??? 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 ??? 802.11b = 1, 2, 5.5, 11Mbps
 ??? 802.11a = 6, 9, 12, 18, 24, 36, 48, 54Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest

Flashing

Fixme This section is in need of cleanup!

Upgrading

Fixme This section is in need of cleanup!

Reverting

Fixme This section is in need of cleanup!

JTAG/Serial Info

JTAG

JTAG Pinouts
Fixme This section is in need of cleanup!
JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

USB Info

Fixme This section is in need of cleanup!

vlan Info

Fixme This section is in need of cleanup!

Pictures

Fixme This section is in need of cleanup!

FCC Pictures

Fixme This section is in need of cleanup!

Notes


Hardware Modification


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.