FANDOM


Your here: Home / Network / Hardware Specific / Cisco-Linksys / E2100L v1.0


Linksys E2100L v1.0
Linksys E2100L v1.0a
Advanced Wireless-N Router

Homepage

E2100L

Wikipedia

Linksys E2100L

WikiDevi

Linksys E2100L

dd-wrt

Linksys E2100L

OpenWRT

Linksys E2100L v1.0

Tomato

Status Unknown

TomatoUSB

Status Unknown

Gargoyle

Status Unknown



NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power.

Specs

Platform

Serial Num. = ?
FCC ID = Q87-E2100L
CPU Type = Atheros AR9130
MIPS Rev = ?
CPU Speed = 400MHz
Bus = ?
Flash Type = Serial
Flash Chip = ?
Flash Size = 8MB
Max Firmware Size = 7995392 bytes
RAM Size = 32MB
RAM Chip = winbond W942566EN-5
nvram Size = ?
Switch = Ralink RTL8306SD 86G93Q1
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/1.5A
Color of LEDs = ?
Size = 7.98" x 6.27" x 1.30"
USB = 1x USB 2.0
Serial Port = 1
JTAG Port = Yes
Supported by TJTAG 3.02 = ?
Supported by dd-wrt as of = v.24 SP2 - build 14935 - 20100812
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = USB, Linksys WRT160NL v1.0

Radio (ath0)

Wireless Radio = Atheros AR9102
WLAN DSP processor = ?
Antenna Connector Type = 2 Detachable (RP-SMA?)
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz
 802.11n Draft = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest

Flashing

You will first need to download this file for the flashing.

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2011/02-17-11-r16214/linksys_E2100L/e2100l-firmware.bin

  1. Go into the linksys stock firmware and choose to reset to defaults.
  2. Once that is finished, set a static ip on your machine to 192.168.1.6 with subnet 255.255.255.0 and gateway 192.168.1.1
  3. Log back into the linksys firmware and find where to update the firmware.
  4. Select the file linked above and then begin the flash procedure, this usually takes 6-7 minutes for it to finish properly, so be patient!
  5. Once it is finished, close your browser, then reopen and browse to http://192.168.1.1 it should want you to set a user/password, do so.
  6. When you are in dd-wrt's webgui, go to Administration > Factory Defaults
  7. Select to "Restore Factory Defaults" This will effectively hard reset the router and ensure integrity of the flash.
  8. Log back into the webgui @ http://192.168.1.1 and set a user/pass and enjoy dd-wrt!
  • Should you want to use DHCP you then may want to unset the static ip from your machine.

Upgrading

Fixme This section is in need of cleanup!

Reverting

Fixme This section is in need of cleanup!

Should you want to revert back to stock firmware then you should be able to download the stock firmware from Linksys's site and flash back using the webgui.

JTAG/Serial Info

JTAG

JTAG Pinouts
Fixme This section is in need of cleanup!
JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

USB Info

Fixme This section is in need of cleanup!

vlan Info

Fixme This section is in need of cleanup!

Pictures

Linksys E2100L v1.0b

FCC Pictures

Linksys E2100L v1.0 FCCa Linksys E2100L v1.0 FCCb Linksys E2100L v1.0 FCCc

Linksys E2100L v1.0 FCCd Linksys E2100L v1.0 FCCe Linksys E2100L v1.0 FCCf

Linksys E2100L v1.0 FCCg Linksys E2100L v1.0 FCCh Linksys E2100L v1.0 FCCi

Linksys E2100L v1.0 FCCk

Notes


Hardware Modification


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.