Fandom

InfoDepot Wiki

Linksys WAP54G v1.0

1,124pages on
this wiki
Add New Page
Talk0 Share

Your here: Home / Network / Hardware Specific / Cisco-Linksys / Linksys WAP54G v1.0


Linksys WAP54G v1.0
Linksys WAP54G

Homepage

WAP54G

Wikipedia

Linksys Routers

dd-wrt

Linksys WAP54G

OpenWRT

Linksys WAP54G

Tomato

Not Supported

TomatoUSB

Not Supported

Gargoyle

?

WARNING - DD-WRT was not originally intended to be loaded on a WAP unit. It was found that it will run but it is a tricky unit to load and have function correctly. Below are a compilation of methods/instructions to assist you with creating a DD-WRT loaded WAP unit.
NOTE: Requires Micro, Do not flash anything else.
NOTE: Requires VINT, Do not flash anything else.
NOTE: Requires K2.4, Do not flash anything else.
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

SpecsEdit

Platform

Serial Num. = MDG0035
FCC ID = PKW-WAP54G
CPU Type = Broadcom BCM4702KPB
MIPS Rev = ?
CPU Speed = 125MHz
Bus = ?
Flash Type = Parallel
Flash Chip = AMD AM29LV320DB-90EI
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 8 or 16
RAM Chip = 2x Dynachips D98SD64 16AH-60310A
nvram Size = ?
Switch = ?
Port-based vlan = No
802.1q vlan = No
Ethernet Port Count = 1-10/100-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = CFE
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = 1x
PoE = No
Power = 5V/2.5A
Color of LEDs = ?
Size = ?
USB = No
Serial Port = No
JTAG Port = Yes
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = ?
dd-wrt K2.4 Support = Micro VINT only
dd-wrt K2.6 Support = No
Special Features = it has 7 leds on front panel and 4MB Flash,
                   Micro VINT only

Radio (wl0)

Wireless Radio = MiniPCI Broadcom BCM4306KFB
WLAN DSP processor = ?
Antenna Connector Type = RP-TNC
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = 2.4GHz
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

FlashingEdit

UpgradingEdit

Fixme This section is in need of cleanup!

RevertingEdit

Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit

JTAGEdit

JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!

SerialEdit

Serial PinoutsEdit
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

PicturesEdit

Fixme This section is in need of cleanup!

FCC PicturesEdit

Linksys WAP54G v1.0 FCCa Linksys WAP54G v1.0 FCCb Linksys WAP54G v1.0 FCCc

Linksys WAP54G v1.0 FCCd Linksys WAP54G v1.0 FCCe Linksys WAP54G v1.0 FCCf

Linksys WAP54G v1.0 FCCg Linksys WAP54G v1.0 FCCh Linksys WAP54G v1.0 FCCi

Linksys WAP54G v1.0 FCCj Linksys WAP54G v1.0 FCCk Linksys WAP54G v1.0 FCCl

Linksys WAP54G v1.0 FCCm Linksys WAP54G v1.0 FCCn Linksys WAP54G v1.0 FCCo

Linksys WAP54G v1.0 FCCp Linksys WAP54G v1.0 FCCq

NotesEdit


Hardware ModificationEdit


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.