FANDOM


Your here: Home / Network / Hardware Specific / Cisco-Linksys / Linksys WAP54G v2.0


Linksys WAP54G v2.0
Linksys WAP54G v2.0a

Homepage

WAP54G

Wikipedia

Linksys Routers

dd-wrt

Linksys WAP54G

OpenWRT

Not for 2MB Devices

Tomato

Not for 2MB Devices

TomatoUSB

Not for 2MB Devices

WARNING - DD-WRT was not originally intended to be loaded on a WAP unit. It was found that it will run but it is a tricky unit to load and have function correctly. Below are a compilation of methods/instructions to assist you with creating a DD-WRT loaded WAP unit.
NOTE: Requires Micro, Do not flash anything else.
NOTE: Requires VINT, Do not flash anything else.
NOTE: Requires K2.4, Do not flash anything else.
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

SpecsEdit

Fixme This section is in need of cleanup!

Platform

Serial Num. = MDG2
FCC ID = Q87-WAP54GV2
CPU Type = Broadcom BCM4712
MIPS Rev = ?
CPU Speed = 200MHz
Bus = ?
Flash Type = Parallel
Flash Chip = AMD AM29LV320DB-90EI
Flash Size = 2MB
Max Firmware Size = ?
RAM Size = 8MB
RAM Chip = Dynachip D98SD64 16AH-60310A
nvram Size = ?
Switch = ? 
Port-based vlan = No
802.1q vlan = No
Ethernet Port Count = 1-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/1A
Color of LEDs = ?
Size = ?
USB = No
Serial Port = Yes
JTAG Port = Yes
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = ?
dd-wrt K2.4 Support = Yes
dd-wrt K2.6 Support = No
Special Features = ?

Radio (wl0)

Wireless Radio = Broadcom ?
WLAN DSP processor = ?
Antenna Connector Type = RP-TNC
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = 2.4GHz
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

Fixme This section is in need of cleanup!

FlashingEdit

Fixme This section is in need of cleanup!

UpgradingEdit

Fixme This section is in need of cleanup!

RevertingEdit

Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit

JTAGEdit

JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!

SerialEdit

Serial PinoutsEdit
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

PicturesEdit

Linksys WAP54G v2.0b Linksys WAP54G v2.0c

FCC PicturesEdit

Linksys WAP54G v2.0 FCCa Linksys WAP54G v2.0 FCCb Linksys WAP54G v2.0 FCCc

Linksys WAP54G v2.0 FCCd Linksys WAP54G v2.0 FCCe Linksys WAP54G v2.0 FCCf

Linksys WAP54G v2.0 FCCg Linksys WAP54G v2.0 FCCh Linksys WAP54G v2.0 FCCi

Linksys WAP54G v2.0 FCCj Linksys WAP54G v2.0 FCCk Linksys WAP54G v2.0 FCCl

Linksys WAP54G v2.0 FCCm Linksys WAP54G v2.0 FCCn Linksys WAP54G v2.0 FCCo

Linksys WAP54G v2.0 FCCp Linksys WAP54G v2.0 FCCq Linksys WAP54G v2.0 FCCr

NotesEdit


Hardware ModificationEdit


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.