NOTE:Resetting to factory defaults via reset button or mtd erase nvram is not safe on this unit until the cfe is rerlaced NOTE:Runs best with VINT firmware. NOTE:Requires K2.4, Do not flash anything else. NOTE:During configuration or flashing a device, the only that should be hooked to the device is the computer and power.
Serial Num. = CGN3
FCC ID = Q87-WT54GV22
CPU Type = Broadcom BCM4712
MIPS Rev = ?
CPU Speed = 200MHz
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = 8MB
Max Firmware Size = ?
RAM Size = 32MB
RAM Chip = ?
nvram Size = ?
Switch = Broadcom BCM5325EKQM
Port-based vlan = Yes
802.1q vlan = Yes
Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3?
boot_wait = off (CFE needs to be replaced)
bootloader = CFE
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/1A
Color of LEDs = ?
Size = ?
USB = No
Serial Port = 2
JTAG Port = Yes
Supported by TJTAG 3.02 = Yes
Supported by dd-wrt as of = ?
dd-wrt K2.4 Support = Yes
dd-wrt K2.6 Support = No
Special Features =
Wireless Radio = Broadcom BCM2050
WLAN DSP processor = ?
Antenna Connector Type = RP-TNC
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = 2.4GHz
802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = 7
Radio Capabilities = ?
Do a HARD reset on the router according to note 1 of the peacock announcement (30/30/30)
Set a static IP on your computer to 192.168.1.7. Subnet mask should be 255.255.255.0.
Connect the lan cable from your computer to a LAN port of your router. Make sure your router is plugged in. Nothing should be connected to your computer or the router except the lan cable between them. Turn your firewall and any wireless computer connections OFF.
Power cycle the router (uplug the power from the router for 30 seconds and then plug it back in)
Open your browser to 192.168.1.1 by putting that in the browser address window of your browser. You should open the linksys webgui and NOT a page that says Management Mode. If you see management mode, power cycle the router again.
Leave the username blank and enter "admin" as the password
Set your computer to a static IP of 192.168.1.7. (or to whatever subnet the router is on) Disable all firewalls and security. Disable wireless on your computer and only have the router connected to the flashing computer by the ethernet cable between the two.
Hard reset or 30/30/30 (If the router supports it, if not, reset to defults in the GUI) prior to flashing. Wait. Check for password page on re-login and change password.
Flash firmware. You can use the webgui except if you have a belkin router. (For belkin use tftp.exe to flash)
Wait...at least three minutes. Lights should return to normal. See important2, below. Failing to wait is how most people brick their routers.
Do a power cycle of the router. (Unplug the cord, count to 30 and plug it back in.)
Wait for the lights to return to normal usually about 2 minutes.
Hard reset or 30/30/30 again (If the router supports it, if not, reset to defults in the GUI). Wait. Check for the password page and re-login to change the password. Then you can reconfigure your settings manually.
Once configured set your computer back to autoIP and autoDNS.
Important1: This Hard reset or 30/30/30 works fine for Asus router, but you do have to power cycle after the reset.
Important2: After you flash the firmware, and before you do the hard reset, the router will be building some nvram settings. YOU MUST WAIT FOR THIS TO FINISH PRIOR TO DOING ANYTHING WITH THE ROUTER INCLUDING A HARD RESET. Usually, you can tell when this process is completed by the WAN light coming on, but it does take several minutes. Go have a beer. There are starting to be more and more people who BRICK their routers by not waiting until the nvram is rebuilt, PRIOR to doing a hard reset. YOU NEED TO WAIT!
In Windows XP, Click Start Button - All Programs - Accessories -
Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Bits per second = 115200
Data Bits = 8
Parity = none
Stop bits = 1
Flow control = none
Click File - Save As, and select a place to save it to so you
don't have to enter the settings again.
After installing putty, run it
Serial line = The COM port your using for serial (ie. COM3)
Speed = 115200
Click on Serial under Connection
Serial line to connect to = same as above (Serial line)
Speed (baud) = 115200
Data bits = 8
Stop bits = 1
Parity = None
Flow control = None
Enter a name for your connection under saved sessions
[comment added 3/23/08 by Bugman916]
Just installed dd-wrt on my WRT54GS v2.0 router. I started with RC 6.2 dd-wrt.v24_mini_wrt54gs through the Linksys interface. Then I used the new dd-wrt mini interface to install RC6.2 dd-wrt.v24_std_generic. Everything seems "ok", I had no problems getting firmware installed.
reminder Default login/pw .. root/admin
I had no trouble installing dd-wrt.v24_std_generic.bin onto my v2 WRT54GS. I didn't need to install mini first, didn't need to play with FTP, just installed it via the firmware update page. It worked without using the reset button. Jax184 07:42, 15 June 2008 (CEST)
[comment added 7/18/08 by koolkat]
Does NOT need VxWorks killer to install due to the fact that factory firmware is linux based.
Installed VINTage Mega firmware after installing VINTage standard, had no problems at all.
"[comment added 10/05/08 by mikeandmonika]"
Installed DD-WRT v24-sp1 (07/26/08) mega-special (upgraded from HyperWRT through GUI). Upgrade took approximately 20 minutes to complete, but all is well and working great.
[comment added 12/20/08 by Corehop]
Successfully installed dd-wrt.v24-9517_VINT_std.bin from factory linksys web GUI. Then tried upgrading to dd-wrt.v24-9517_VINT_mega.bin using the DDWRT web GUI, but when the router reset, it would not respond to pings and I had to short pins 15 and 16 on the flash chip and TFTP the Linksys firmware.
Comment galengish at 10:34 (EST) on 06 Jan 2009: I flashed a Linksys WRT54GS v2 router last night from original firmware to DD_WRT v24 (05/20/2008) std in one shot. This was performed via Internet Explorer and the Web GUI via Ethernet cable. The flash was successful on the first try and it is now successfully working as a client-bridge with another WRT54GS v7 running original Linksys firmware.
Comment Milkman at 8:47 (CST) on 26 Mar 2009: I just installed v24-sp1 mega from the Linksys firmware and it seems to have installed without a hitch, although I haven't had a chance to play around much yet. It is indicating "Error" on the title bar in my browser, but this may be associated with the lack of WAN connectivity for the router at this point. Will update should I find any significant errors/problems. (I hope I get the formatting correct here, please bear with me as I am new to wiki submissions)
Updated 10 Apr 2009: OK, backing up to v24 doesn't cause the "error" reporting on the browser (like in Электронный документооборот, seems to be something with the SP1 release. Haven't checked change logs, but seems very happy with v24 mega.