Fandom

InfoDepot Wiki

Netgear WGR826V

1,124pages on
this wiki
Add New Page
Talk0 Share

Your here: Home / Network / Hardware Specific / Netgear / WGR826V


Netgear WGR826V
Netgear WGR826Va
54 Mbps Wireless Router with Phone Adapter

Homepage

WGR826V

Wikipedia

?

WikiDevi

?

dd-wrt

donation board needed for port

OpenWRT

Not Supported

Tomato

Not Supported

TomatoUSB

Not Supported

Gargoyle

Not Supported

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = PY3WGR826V
CPU Type = Intel IXP425
MIPS Rev = ?
CPU Speed = 266MHz
Bus = ?
Flash Type = ?
Flash Chip = Intel TE28F128
Flash Size = 16MB
Max Firmware Size = ?
RAM Size = 32MB
RAM Chip = ?
nvram Size = ?
Switch = Kendin KS8995X 5-Port switch
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-WAN 4-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = Yes
PoE = ?
Power = 12V/1.25A
Color of LEDs = 7 green/amber LEDs and 2 green LEDs
Size = ?
USB = Yes
Serial Port = RS-232 Console
JTAG Port = Yes
Supported by TJTAG/Version = ?
Special Features = ?

Radio

Wireless Radio = Ralink RT2500 mini PCI card (must be replaced for dd-wrt)
WLAN DSP processor = ?
Antenna Connector Type = One Omni-directional Fixed Antenna
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = ?
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest

Flashing

Fixme This section is in need of cleanup!

Upgrading

Fixme This section is in need of cleanup!

Reverting

Fixme This section is in need of cleanup!

JTAG/Serial Info

JTAG

JTAG Pinouts
Fixme This section is in need of cleanup!
JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

USB Info

Fixme This section is in need of cleanup!

vlan Info

Fixme This section is in need of cleanup!

Pictures

Fixme This section is in need of cleanup!

FCC Pictures

Fixme This section is in need of cleanup!

Notes


Hardware Modification


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.