FANDOM


Your here: Home / Network / Hardware Specific / Netgear / WNDR4000


Netgear WNDR4000
Netgear WNDR4000 a
N750 Wireless Dual Band Gigabit Router

Homepage

WNDR4000

Wikipedia

?

WikiDevi

WNDR4000

dd-wrt

Supported

OpenWRT

Not Supported

Tomato

Not Supported

TomatoUSB

Not Supported

Gargoyle

Not Supported

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = PY310400144
Industry Canada ID = 4054A-10400144
CPU Type = Broadcom (BCM4718A) BCM4718A1KFBG CS1104P11 118099N1
MIPS Rev = ?
CPU Speed = 480 MHz
Bus = ?
Flash Type = ?
Flash Chip = Macronix MX25L6445
Flash Size = 8MB
Max Firmware Size = ?
RAM Size = 64MB
RAM Chip = Winbond W9751G6JB
nvram Size = 64kb
Switch = Broadcom BCM53115
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100/1000 4-10/100/1000
Wired Standard = IEEE 802.3/3u/3ab
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/2.5A
Color of LEDs = ?
Size = 223 x 153 x 31 mm (8.8 x 6.0 x 1.2 in)
USB = 1x USB 2.0
Serial Port = Yes
JTAG Port = ?
Supported by TJTAG/Version = ?
Special Features = ?

Radio (wl0)

Wireless Radio = Broadcom BCM4718A1 (SoC)
WLAN DSP processor = ?
Antenna Connector Type = 2x2, Internal, U.FL
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Radio (wl1)

Wireless Radio = Broadcom BCM4331
WLAN DSP processor = ?
Antenna Connector Type = 3x3, Internal, U.FL
Wireless Standard = IEEE 802.11a/n
WiFi Operating Frequency = 5GHz
 802.11n = up to 450Mbps
 802.11a = 6, 9, 12, 18, 24, 36, 48, 54Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest

Flashing

Fixme This section is in need of cleanup!

Upgrading

Fixme This section is in need of cleanup!

Reverting

Fixme This section is in need of cleanup!

JTAG/Serial Info

JTAG

JTAG Pinouts
Fixme This section is in need of cleanup!
JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

USB Info

Fixme This section is in need of cleanup!

vlan Info

Fixme This section is in need of cleanup!

Pictures

Netgear WNDR4000 b Netgear WNDR4000 c Netgear WNDR4000 d

Netgear WNDR4000 e Netgear WNDR4000 f

FCC Pictures

Fixme This section is in need of cleanup!

Notes

Serial Boot Log


Decompressing..........done
Decompressing..........done


CFE for WNDR4000 version: v1.0.4
Build Date: Tue Nov 30 17:04:18 CST 2010
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 128 64KB blocks; total size 8MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 2010.09.30.0
CPU type 0x19740: 480MHz
Tot mem: 65536 KBytes

Device eth0: hwaddr C4-3D-C7-70-A1-E9, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Linux version 2.6.22 (peter@dev2) (gcc version 4.2.3) #10 Mon Apr 25 19:58:10 CS
T 2011
CPU revision is: 00019740
Found an ST compatible serial flash with 128 64KB blocks; total size 8MB
Determined physical RAM map:
memory: 03fff000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0 -> 16383
HighMem 16383 -> 16383
early_node_map[1] active PFN ranges
0: 0 -> 16383
Built 1 zonelists. Total pages: 16383
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit

Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM4716 rev 1 at 480 MHz
Using 240.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60016k/65532k available (3087k kernel code, 5460k reserved, 592k data, 2
04k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
PCI: Using membase 8000000
PCI: Initializing host
PCI: Reset RC
PCI: no core
PCI: Fixing up bus 0
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.8)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
loop: module loaded
PPP generic driver version 2.4.2
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
pflash: found no supported devices
sflash: squash filesystem with lzma found at block 1646
Creating 15 MTD partitions on "sflash":
0x00000000-0x00040000 : "boot"
0x00040000-0x00740000 : "linux"
0x0019bb70-0x00740000 : "rootfs"
0x00740000-0x00750000 : "ML1"
0x00750000-0x00760000 : "ML2"
0x00760000-0x00770000 : "ML3"
0x00770000-0x00780000 : "ML4"
0x00780000-0x00790000 : "ML5"
0x00790000-0x007a0000 : "ML6"
0x007a0000-0x007b0000 : "ML7"
0x007b0000-0x007c0000 : "T_Meter1"
0x007c0000-0x007d0000 : "T_Meter2"
0x007d0000-0x007e0000 : "POT"
0x007e0000-0x007f0000 : "board_data"
0x007f0000-0x00800000 : "nvram"
u32 classifier
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
6WIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
Warning: unable to open an initial console.
Failed to execute /init
[sighandler]: No more events to be processed, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
Reading board data...
WSC UUID: 0xdb3b6fcc090e922939fd2363c56c8a2d
NTP synchronized date/time: 00-00-00
MAC address of 1st STA connected: 1C-4B-D6-BD-AD-87
invalid RF magic!
No RF parameters! Use default.
Initialise conn table 2048 entries
Hit enter to continue...wlconf: PHYTYPE: 4
wlconf: PHYTYPE: 7
wlconf: PHYTYPE: 4
wlconf: PHYTYPE: 7
killall: upnp: no process killed
UPnP daemon is ready to run
killall: wps_monitor: no process killed
killall: wps_ap: no process killed
killall: wps_enr: no process killed

      1. wps_wfi_init(): <wl0_wfi_enable=(null)><wl1_wfi_enable=(null)>WFI is not ena
        bled ###
        Reading board data...
        WSC UUID: 0xdb3b6fcc090e922939fd2363c56c8a2d
        shm ID: 0
        Get a correct Segment_ID: 0 and semaphore ID:0
        info, udhcp server (v0.9.8) started
        error, unable to parse 'option wins '
        error, unable to parse 'option domain '
        POT integrity check OK.
        POT time is up.
        Info: No FWPT default policies.
        httpd: socket bound in 0.0.0.0:80.
        IOCTL_AG_REGION_SET: English
        Start DHCP client daemon
        info, udhcp client (v0.9.8) started
        eth0: No such process
        route: ioctl 0x890c failed: No such process
        killall: dhcp6c: no process killed
        killall: IPv6-relay: no process killed
        killall: pppdv6: no process killed
        killall: rtsol: no process killed
        killall: dhcp6s: no process killed
        killall: radvd: no process killed
        route: ioctl 0x890c failed: No such process
        killall: dhcp6s: no process killed
        killall: radvd: no process killed
        Hit enter to continue...

Hardware Modification


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.