Fandom

InfoDepot Wiki

Netgear WNR1000 v3.0

1,124pages on
this wiki
Add New Page
Talk0 Share

Your here: Home / Network / Hardware Specific / Netgear / WNR1000 v3.0


Netgear WNR1000 v3.0
Netgear WNR1000a

Homepage

WNR1000

Wikipedia

Netgear

dd-wrt

WIP

OpenWRT

?

Tomato

?

TomatoUSB

Not Supported

Gargoyle

?

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

SpecsEdit

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = PY309300117
CPU Type = Broadcom BCM5356A1KFBG CA0934 P11 933734 N1A (BCM5356A1 SoC)
MIPS Rev = ?
CPU Speed = 300MHz
Bus = ?
Flash Type = Serial
Flash Chip = ?
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 16MB
RAM Chip = ISSI IC42S16800E-6TL XA864100X 0931
nvram Size = ?
Switch = Broadcom BCM5356A1KFBG CA0934 P11 933734 N1A (BCM5356A1 SoC)
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = CFE
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = ?
Color of LEDs = ?
Size = 28 x 175 x 118 mm (1.1 x 6.9 x 4.7 in)
USB = ?
Serial Port = 1
JTAG Port = Yes
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = WIP
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = serial flash chip device! same HW as WGR614 v10

Radio

Wireless Radio = Broadcom BCM5356A1KFBG CA0934 P11 933734 N1A (BCM5356A1 SoC)
WLAN DSP processor = ?
Antenna Connector Type = External Fixed
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz
 802.11n = up to 150Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps N1A
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

FlashingEdit

Fixme This section is in need of cleanup!

UpgradingEdit

Fixme This section is in need of cleanup!

RevertingEdit

Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit

JTAGEdit

JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!

SerialEdit

Serial PinoutsEdit
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

vlan InfoEdit

Fixme This section is in need of cleanup!

PicturesEdit

Netgear WNR1000b

FCC PicturesEdit

NotesEdit


Hardware ModificationEdit


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.