Your here: Home / Network / Hardware Specific / Netgear / WNR2000 v1.0

Netgear WNR2000 v1.0
Netgear WNR2000a


Netgear WNR2000




Not Supported






Not Supported



NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.


Fixme This section is in need of cleanup!


Serial Num. = ?
FCC ID = PY308200083
CPU Type = Atheros AR9132
MIPS Rev = ?
CPU Speed = 400MHz
Bus = ?
Flash Type = Serial
Flash Chip = MX 25L3205DMI
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 32MB
RAM Chip = Hynix HY5DU561622FTP-D43
nvram Size = ?
Switch = Atheros AR8216
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = U-Boot
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = ?
Color of LEDs = ?
Size = ?
USB = No
Serial Port = Yes
JTAG Port = Yes
Supported by TJTAG/Version = No
Supported by dd-wrt as of = ?
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features =

Radio (ath0)

Wireless Radio = Atheros AR9103 (3x3 WiSoC)
WLAN DSP processor = ?
Antenna Connector Type = Internal
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit


Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit


JTAG PinoutsEdit

JTAG pins were found by removing the BGA from a WNR2000 and a TP-Link WR-1043ND (AR9132 with JTAG header) and comparing the PCB traces. The top side of the PCB is the one with the heatsinks.

^ Name ^ BGA pin ^ Top/Bottom of PCB ^ Location on PCB ^
| TMS   | G20 | bottom | R335 towards C324 |
| TDO   | G21 | top    | TP34 |
| nTRST | F22 | top    | R68 toward CPU  |
| TCK   | F21 | top    | R336 toward CPU |
| TDI   | G22 | top    | R334 toward CPU |
| nSRST | D22 | top    | U8 toward R262  |

(Be aware that there is no "I" row in the BGA counting!)

JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!


Serial PinoutsEdit

The serial port is at JP1: 115200 8N1 at 3.3V. Pins are, from left with the Ethernet ports above:

[Vcc] [Tx] [Rx] [GND]
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

vlan InfoEdit

Fixme This section is in need of cleanup!


Netgear WNR2000b

FCC PicturesEdit

Fixme This section is in need of cleanup!


Hardware ModificationEdit

Ad blocker interference detected!

Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.