FANDOM


Your here: Home / Network / Hardware Specific / Rosewill / RNX-GX4


Rosewill RNX-GX4
Rosewill RNX-GX4a

Homepage

Rosewill RNX-GX4

Wikipedia

?

dd-wrt

Supported Devices Rosewill

OpenWRT

?

Tomato

?

TomatoUSB

Not Supported

Gargoyle

?

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = W6RRNX-GX4
CPU Type = Broadcom BCM5354KFBG HA0927 P13 925978 N2 (BCM5354 SoC)
MIPS Rev = ?
CPU Speed = 240MHz
Bus = ?
Flash Type = Serial
Flash Chip = ?
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 16MB
RAM Chip = ?
nvram Size = ?
Switch = Broadcom BCM5354KFBG HA0927 P13 925978 N2 (BCM5354 SoC)
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 9V/0.7A
Color of LEDs = ?
Size = ?
USB = No
Serial Port = Yes
JTAG Port = Yes
Supported by TJTAG 3.02 = ?
Supported by dd-wrt as of = v.24 SP2 - build 13780 - 20100129
dd-wrt K2.4 Support = Yes
dd-wrt K2.6 Support = No
Special Features = ?

Radio (wl0)

Wireless Radio = Broadcom BCM5354KFBG HA0927 P13 925978 N2 (BCM5354 SoC)
Antenna Connector Type = RP-SMA
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = 2.4GHz - 2.4835GHz
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest

Flashing

Fixme This section is in need of cleanup!

Upgrading

Fixme This section is in need of cleanup!

Reverting

Fixme This section is in need of cleanup!

JTAG/Serial Info

JTAG

JTAG Pinouts
Fixme This section is in need of cleanup!
JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

vlan Info

Fixme This section is in need of cleanup!

Pictures

Rosewill RNX-GX4b

FCC Pictures

Rosewill RNX-GX4 FCCa Rosewill RNX-GX4 FCCb Rosewill RNX-GX4 FCCc

Rosewill RNX-GX4 FCCd Rosewill RNX-GX4 FCCe Rosewill RNX-GX4 FCCf

Rosewill RNX-GX4 FCCg Rosewill RNX-GX4 FCCh Rosewill RNX-GX4 FCCi

Rosewill RNX-GX4 FCCj Rosewill RNX-GX4 FCCk Rosewill RNX-GX4 FCCl

Notes


Hardware Modification


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.