FANDOM


Your here: Home / Network / Hardware Specific / TP-Link / TL-WR1043ND v1.6


TP-Link TL-WR1043ND v1.6
TP-Link TL-WR1043NDa

Homepage

TL-WR1043ND

Wikipedia

?

dd-wrt

?

OpenWRT

TL-WR1043ND

Tomato

?

TomatoUSB

Not Supported

Gargoyle

?

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

SpecsEdit

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = ?
CPU Type = Atheros AR9132-BC1E (AR9132)
MIPS Rev = ?
CPU Speed = 400MHz
Bus = ?
Flash Type = Serial
Flash Chip = 25P64V6P 99AJAV5 MYS722
Flash Size = 8MB
Max Firmware Size = ?
RAM Size = 32MB
RAM Chip = HY5DU561622FTP-D43
Switch = Realtek RTL8366RG A1G17A2 GA05B
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100/1000-WAN 4-10/100/1000-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/1.5A
Color of LEDs = ?
Size = ?
USB = 1 USB 2.0 Port
Serial Port = Yes
JTAG Port = Yes
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = WR1043ND v.24 SP2 - build 13972 - 20100223
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
dd-wrt Notes = N clients connect only at G tx/rx rate,
               everything else working
Special Features = ?

Radio (ath0)

Wireless Radio = Atheros AR9103 3x3 MIMO
WLAN DSP processor = ?
Antenna Connector Type = 3dBi Detachable RP-SMA Omni Directional Antenna X 3
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4~2.4835GHz
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

FlashingEdit

Fixme This section is in need of cleanup!

UpgradingEdit

Fixme This section is in need of cleanup!

RevertingEdit

Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit

JTAGEdit

JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!

SerialEdit

Serial PinoutsEdit
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

USB InfoEdit

Fixme This section is in need of cleanup!

vlan InfoEdit

Fixme This section is in need of cleanup!

PicturesEdit

TP-Link TL-WR1043NDb TP-Link TL-WR1043NDc TP-Link TL-WR1043NDd

TP-Link TL-WR1043NDe

FCC PicturesEdit

Fixme This section is in need of cleanup!


NotesEdit

Hardware ModificationEdit

Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.