TP-Link TL-WR941ND v3.2
Talk0
1,179pages on
this wiki
this wiki
Your here: Home / Network / Hardware Specific / TP-Link / TL-WR941ND v3.2
 |
This article is a stub. Please help InfoDepot Wiki by expanding it, adding pictures, and improving existing text.
|
| TP-Link TL-WR941ND v3.2 | |
|---|---|
 | |
|
Homepage | |
|
Wikipedia |
? |
|
dd-wrt |
? |
|
OpenWRT | |
|
Tomato |
? |
|
TomatoUSB |
Not Supported |
|
Gargoyle |
? |
Contents |
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.
Specs
Edit
This section is in need of cleanup!
Platform
Serial Num. = ? FCC ID = TE7WR941NX CPU Type = Atheros AR9132 MIPS Rev = ? CPU Speed = 400MHz Bus = ? Flash Type = SPI Flash Chip = Intel S33 Flash Size = 4MB Max Firmware Size = ? RAM Size = 32MB RAM Chip = ? nvram Size = ? Switch = ? Port-based vlan = ? 802.1q vlan = ? Ethernet Port Count = 1-WAN 4-LAN Wired Standard = IEEE 802.3? boot_wait = ? bootloader = U-boot Flash Card Socket/Type = no SD/MMC Mod Support = no MiniPCI slots = no PoE = ? Power = 9V/.85A Color of LEDs = ? Size = ? USB = Mod to add Serial Port = yes JTAG Port = no Supported by TJTAG/Version = ? Supported by dd-wrt as of = v.24 sp2 - build 14581 - 20100609 dd-wrt K2.4 Support = ? dd-wrt K2.6 Support = ? Special Features = use v3.0 build for flashing v3.5
Radio
Wireless Radio = Atheros AR9103 3x3 MIMO @ 20dBm WLAN DSP processor = ? Antenna Connector Type = ? Wireless Standard = IEEE 802.11b/g/n WiFi Operating Frequency = ? 802.11n = up to 300Mbps 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b = 1, 2, 5.5, 11Mbps Radio cor_rev = ? Radio Capabilities = ?
Links of InterestEdit
This section is in need of cleanup!
FlashingEdit
This section is in need of cleanup!
UpgradingEdit
This section is in need of cleanup!
RevertingEdit
This section is in need of cleanup!
JTAG/Serial InfoEdit
JTAGEdit
JTAG PinoutsEdit
This section is in need of cleanup!
JTAG RecoveryEdit
This section is in need JTAG Recovery Instructions!
SerialEdit
Serial PinoutsEdit
This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories -
Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
Bits per second = 115200
Data Bits = 8
Parity = none
Stop bits = 1
Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you
don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open
Serial RecoveryEdit
This section is in need of Serial Recovery Instructions!
USB InfoEdit
This section is in need of cleanup!
vlan InfoEdit
This section is in need of cleanup!
PicturesEdit
This section is in need of cleanup!
FCC PicturesEdit
This section is in need of cleanup!
