FANDOM


Your here: Home / Network / Hardware Specific / Ubiquiti / RouterStation Pro


Ubiquiti RouterStation Pro
Ubiquiti RouterStation Pro a
???

Homepage

RouterStation Pro

Wikipedia

?

WikiDevi

?

dd-wrt

Not Supported

OpenWRT

RouterStation Pro

Tomato

Not Supported

TomatoUSB

Not Supported

Gargoyle

Not Supported

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.
NOTE: DD-WRT Activation Required.

Specs

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = ?
CPU Type = Atheros AR7100
MIPS Rev = ?
CPU Speed = 680MHz (Option to overclock to 800)
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = 64MB
RAM Size = 128MB
RAM Chip = ?
nvram Size = ?
Switch = Atheros AR8316
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-WAN 4-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = RedBoot
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = 3x 32-bit
PoE = 802.3af 48V compatible
Power = 5-24V
Color of LEDs = ?
Size = ?
USB = 1x 2.0
Serial Port = 1
JTAG Port = 1
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = v.24 pre sp2 - build 12909 - 20090915
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = ?

Radio

Wireless Radio = depends on card

Links of Interest

Flashing

Fixme This section is in need of cleanup!

Upgrading

Fixme This section is in need of cleanup!

Reverting

Fixme This section is in need of cleanup!

JTAG/Serial Info

JTAG

JTAG Pinouts

JTAG Port "J4" 14 Pin header

TRST 1o o2  GND
TDI  3o o4  GND
TDO  5o o6  GND
TMS  7o o8  GND
TCK  9o o10 GND
RST 11o o12 NC
NC  13o o14 3.3VDC

JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts

UART J3 6 pin Header Terminal Settings 115200 baud, 8 bits, nor parity, 1 stop bit.

1o 3.3VDC
2o RX
3o NC
4o NC
5o TX
6o GND
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

USB Info

Fixme This section is in need of cleanup!

vlan Info

Fixme This section is in need of cleanup!

Pictures

Ubiquiti RouterStation Pro b

FCC Pictures

Fixme This section is in need of cleanup!

Notes

For more information: http://www.ubnt.com/support/rspro

Hardware Modification


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.