FANDOM


Your here: Home / Network / Hardware Specific / Ubiquiti / UNIFI


Ubiquiti UNIFI
Ubiquiti UNIFI a

Homepage

unifi

Wikipedia

?

dd-wrt

WIP

OpenWRT

?

Tomato

?

TomatoUSB

Not Supported

Gargoyle

?

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

SpecsEdit

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = ?
CPU Type = Atheros (AR7240)
MIPS Rev = ?
CPU Speed = ???Mhz
Bus = ?
Flash Type = Serial
Flash Chip = MX25L6405D
Flash Size = 8MB
Max Firmware Size = ?
RAM Size = 64MB
RAM Chip = ?
nvram Size = ?
Switch = N/A
Port-based vlan = ?
802.1q vlan = Yes
Ethernet Port Count = 1-10/100-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = U-boot
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = Passive
Power = 24V/1A
Color of LEDs = ?
Size = ?
USB = No
Serial Port = 1
JTAG Port = 1
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = WIP
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = ?

Radio

Wireless Radio = Atheros AR9287
WLAN DSP processor = ?
Antenna Connector Type = Internal
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

FlashingEdit

Fixme This section is in need of cleanup!

UpgradingEdit

Fixme This section is in need of cleanup!

RevertingEdit

Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit

JTAGEdit

JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!

SerialEdit

Serial PinoutsEdit
3.3V 1 o
 SIN 2 o
SOUT 3 o
 GND 4 o
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

vlan InfoEdit

Fixme This section is in need of cleanup!

PicturesEdit

Ubiquiti UNIFI b

FCC PicturesEdit

Fixme This section is in need of cleanup!

NotesEdit


Hardware ModificationEdit


Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.